SHOWTEC 40081 User Manual Download Page 9

 

 

 

8 

 

  

 

 

Phantom 250 Spot 

Product code: 40081 

 

Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is 
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for 
more information, as servicing can be performed only by instructed or skilled persons. 

 

If the device is dropped or struck, disconnect the device from the electrical power supply 
immediately. 

 

If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it 
on immediately. Let the device reach room temperature before switching it on, otherwise it may be 
damaged by the formed condensation. 

 

If the device fails to work properly, discontinue the use immediately. 

 

Attention 
For professional use only 
This device shall be used only for the purposes it is designed for. 

This device is designed to be used as a spot light moving head. Any incorrect use may lead to hazardous 
situations and result in injuries and material damage. 

 

This device is not suitable for households and for general lighting. 

 

This device is not designed for permanent operation. 

 

This device does not contain user-serviceable parts. Unauthorized modifications to the device will 
render the warranty void. Such modifications may result in injuries and material damage. 

 

Attention 
Before each use, examine the device visually for any defects. 

Make sure that: 

 

All screws used for installing the device or parts of the device are tightly fastened and are not 
corroded. 

 

The safety devices are not damaged. 

 

There are no deformations on housings, fixations and installation points. 

 

The lens is not cracked or damaged. 

 

The power cables are not damaged and do not show any material fatigue. 

 

Attention 
Do not expose the device to conditions that exceed the rated IP class conditions. 

This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater 
than 12 mm, such as fingers, and no protection against harmful ingress of water.  

 

 

Summary of Contents for 40081









































Reviews: