manualshive.com logo in svg

Shinko CIT-200, Instruction Manual

The Shinko CIT-200 Instruction Manual is a comprehensive user guide for operating the CIT-200 device. This manual is available for free download, ensuring easy access to essential product information. Unlock the full potential of your CIT-200 with our detailed manual, conveniently accessible from manualshive.com.

Share
Download
background image

3 

1. Installation precautions 

 
 

     

   

Warning 

Turn the power supplied to the instrument OFF before mounting.   
Working or touching the terminal with the power switched ON may result in severe 
injury or death due to Electric Shock. 

       

 

 
 

     

   

Caution 

 

This instrument is intended to be used under the following environmental conditions (IEC61010-1): 

 Overvoltage 

category 

, Pollution degree 2 

 

Mount the unit in a place with: 

(1) A minimum of dust, and an absence of corrosive gases 
(2) No flammable, explosive gases 

 

(3) No mechanical vibrations or shocks 

 

(4) No exposure to direct sunlight, an ambient temperature of 0 to 50  (32 to122 ) that does not 

change rapidly 

 

(5) An ambient non-condensing humidity of 35 to 85%RH 

 

(6) No large capacity electromagnetic switches or cables through which large current is flowing 

 

(7) No water, oil or chemicals or where the vapors of these substances can come into direct contact 

with the unit 

 
 

Note: Although the case of this instrument is made of flame resisting resin, do not install   

this instrument near flammable material.   
Avoid setting this instrument directly on flammable material. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for CIT-200





















































Reviews:

No comments

Related manuals for CIT-200

ACS 3200 Series Operation And Instruction Manual preview
3200 Series
Brand: ACS Pages: 56
Palazzetti P1 Installation Instructions, Use And Maintenance preview
P1
Brand: Palazzetti Pages: 112
Panasonic WJHD309A - DIGITAL DISK RECORDER Network Operating Instructions preview
WJHD309A - DIGITAL DISK RECORDER
Brand: Panasonic Pages: 79
NAD M52 Owner'S Manual preview
M52
Brand: NAD Pages: 10
IFM AC1401 Device Manual preview
AC1401
Brand: IFM Pages: 175
IFM VSE150 Installation Instructions preview
VSE150
Brand: IFM Pages: 5
Mackie Spike Getting Started Manual preview
Spike
Brand: Mackie Pages: 18
Mackie SDR24/96 Quick Start Manual preview
SDR24/96
Brand: Mackie Pages: 2
Mackie HDR 24 User Manual preview
HDR 24
Brand: Mackie Pages: 8
Mackie ProFX16 User Manual preview
ProFX16
Brand: Mackie Pages: 7
Pahlen Jet Swim 2000 Manual preview
Jet Swim 2000
Brand: Pahlen Pages: 20
Paia P9700S Overview preview
P9700S
Brand: Paia Pages: 7
Raymarine ST60+ SPEED INSTRUMENT Owner'S Handbook Manual preview
ST60+ SPEED INSTRUMENT
Brand: Raymarine Pages: 60
Raymarine Maxiview ST80 Operation Manual preview
Maxiview ST80
Brand: Raymarine Pages: 15
RaycoWylie i3500 Quick Start Manual preview
i3500
Brand: RaycoWylie Pages: 9
Raven SmarTrax Calibration & Operation Manual preview
SmarTrax
Brand: Raven Pages: 58
Raven Sidekick Pro Quick Installation Reference preview
Sidekick Pro
Brand: Raven Pages: 26
Ravo MP-10 Owner'S Manual preview
MP-10
Brand: Ravo Pages: 114

Brands by name

Popular brands

Load more brands