Shindaiwa DGK150D Owner'S And Operator'S Manual Download Page 7

Page: 7 / 58



Before starting operation, always be sure to turn off all switches of equipment using the

generator and all breakers to OFF.



Do not move the generator during operation.



Do not operate the generator if it has been modified or any parts have been removed.

CAUTION : PROPERTY DAMAGE



If using this generator for medical equipment, check before use with the medical equipment

manufacturer, doctor, hospital or similar entity.



Check that the generator output setting, output terminal connection and load power source

are consistent.



Cable burnout can occur due to generated heat if the load current exceeds the allowable

current of the cable.



The voltage drop between cables is large if the cable is excessively long or thin, resulting in

decreased input voltage to equipment using the generator, thereby causing decreased
performance, faulty operation and malfunction.



Warning/Caution Label Locations

If warning or caution labels become damaged and difficult to read, replace with new
labels in the indicated locations. Order labels using part number indicated in the
parenthesis.

①

Warning

：

Injury

（

Part no.

：

X505-007550

）

②

Warning

：

Electric Shock

（

Part no.

：

X505-007560

）

③

Caution

：

GM Spec LLC

（

Part no.

：

X505-004650

）

④

Warning

／

Caution

（

Part no.

：

X505-007571

）

⑤

Warning

：

Keep Terminal

（

Part no.

：

X505-007580

）

⑥

Caution

：

Neutral bonded to frame

（

Part no.

：

X505-004750

）

⑦

Caution

：

Do not change

（

Part no.

：

X505-004620

）

Summary of Contents for DGK150D



























































Search results

Summary of Contents for DGK150D

Reviews:

Related manuals for DGK150D

Brands by name

Popular brands

Shindaiwa DGK150D, Owner'S And Operator'S Manual

Search results

Summary of Contents for DGK150D

Reviews:

Related manuals for DGK150D

Brands by name

Popular brands