Shindaiwa DGK150D Owner'S And Operator'S Manual Download Page 24 | Manualshive

Page: 24 / 58

background image

21

6.

Transporting/Installing

6-1. Transport Procedures

WARNING : INJURY



Always be sure to use lifting hooks when lifting up the generator. The other thing could

result in the generator falling.



This lifting hook is designed to lift the generator only. Do not lift any additional

added weight such as fuel tanks and/or trailers with this lifting hook.



No persons should be under a lifted generator.

CAUTION : INJURY



Always be sure to use lifting hooks when lifting up the generator, and raise it

slowly at vertical angle completely.



Personnel performing lifting work must wear protective gear such as helmets,

safety shoes and gloves.



Do not move the generator during operation.



Lifting Procedures

Always be sure to use lifting hooks when lifting up the generator, and raise it slowly at
vertical angle completely.

< NOTE >



Handle this generator with extreme care when raising, lowering and transporting. Rough

handling of this generator may result in damage or malfunction.

Lifting Hook

«
...
22
23
24
25
26
...
»

Summary of Contents for DGK150D



























































Reviews:

No comments

Related manuals for DGK150D

Brand: Cambridge Audio Pages: 4

Brand: Cambridge Audio Pages: 2

Brand: Net Optics Pages: 15

Brand: RGBlink Pages: 42

Brand: M-Audio Pages: 24

Brand: N-Tron Pages: 2

Brand: ADF Web Pages: 25

Brand: Kramer Pages: 30

TopTronic E Solar TTE-SOL

Brand: Hoval Pages: 95

Rossini Transport

Brand: DCS Pages: 31

Brand: CEL-MAR Pages: 28

Brand: Barco Pages: 2

Brand: CYP Pages: 16

Brand: Cablematic Pages: 3

Brand: e+p Pages: 2

Brand: Accorroni Pages: 44

Brand: Innova Pages: 20

Brand: M-Audio Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands