Shindaiwa DGK150D Owner'S And Operator'S Manual Download

Page: 9 / 58

2-2. Ambient Conditions

Use this generator in ambient conditions as described below. Failure to provide these
conditions can result in problems such as malfunction, insufficient output and reduced
durability.

■

Ambient temperature: 5 to 104 ° F ( -15 to 40 ° C )

■

Relative humidity:

85% or less

■

Elevation:

3280 ft ( 1000 m ) or less

3. Applications



Power source for submerged pumps and similar civil engineering equipment.



Power source for lighting and similar equipment.



Power source for electrical tools and household appliances.

4. Part Names

4-1. External View/Part Names

CAUTION : PROPERTY/SECONDARY DAMAGE



Do not use for any application other than those listed above.



If using this generator for medical equipment, check before use with the

medical equipment manufacturer, doctor, hospital or similar entity.

Lifting Hook

Operation Panel Door

Summary of Contents for DGK150D



























































Search results

Summary of Contents for DGK150D

Reviews:

Related manuals for DGK150D

Brands by name

Popular brands

Shindaiwa DGK150D, Owner'S And Operator'S Manual

Search results

Summary of Contents for DGK150D

Reviews:

Related manuals for DGK150D

Brands by name

Popular brands