Shimano Alfine S7000 Series Dealer'S Manual Download Page 43

Page: 43 / 47

To be continued on next page

MAINTENANCE

In the case of 11-speed internal geared hub (Oil maintenance kit: Y13098023)

(A)

(B)

(C)

(D)

Attach the bleed nipple with tube
attached to the hub shell.

(A)

Hub shell

(B)

Tube

(C)

10mm spanner

(D)

Bleed nipple

Tightening torque

1 - 3 N·m

TECH TIPS

Check that the O-ring is properly installed on
the bleed nipple.

(A)

(B)

With the piston of the syringe pushed
fully in, firmly connect the syringe to the
tube.

(A)

Tube

(B)

Syringe

(z)

Insert the syringe between the spokes,
and slowly turn the wheel forward until
the oil port is facing down.

(z)

Turn in forward direction

Wait about 5 minutes with the hub kept still and not turning so that the oil settles.

Summary of Contents for Alfine S7000 Series
















































Search results

Summary of Contents for Alfine S7000 Series

Reviews:

Related manuals for Alfine S7000 Series

Brands by name

Popular brands

Shimano Alfine S7000 Series, Dealer'S Manual

Search results

Summary of Contents for Alfine S7000 Series

Reviews:

Related manuals for Alfine S7000 Series

Brands by name

Popular brands