background image

Preparation

20 

• You can also fold the LCD monitor into

the camcorder with the screen facing
out for watching playback on the
monitor.

3

Hold down the Lock
button and set the
POWER switch to
CAMERA or VCR.

• A picture displays on

the LCD monitor.

Notes:

• Battery consumption is larger when the LCD

monitor is open. Use the viewfinder instead of
the LCD monitor when you want to save battery
power.

• Use the viewfinder if the LCD screen becomes

difficult to see under bright daylight.

Using the LCD Monitor

You can use the LCD monitor to play back
recordings that you have made or to watch the
subject during recording.

1

Press the LCD monitor PUSH OPEN
release, and open the LCD monitor to a
90˚ angle to the camcorder body.

2

Adjust the LCD monitor to an angle that
allows easy viewing of the on-screen
picture.

• The LCD monitor rotates 270˚ vertically.

Caution: Do not try to rotate the LCD monitor
vertically until the monitor is completely
opened.

90˚

180

90

Closing the LCD monitor

Return the LCD monitor to the vertical 90˚
position with the screen facing in, and fold it
into the camcorder until it clicks into place.

Cautions:
• Do not use excessive force when moving the

LCD monitor.

• When closing the LCD monitor, do not tilt it;

otherwise the monitor may not close properly
and may become damaged.

• Do not pick up the camcorder by the LCD

monitor.

• Do not place the camcorder with the LCD

monitor screen facing down.

Note:

• Close the LCD monitor completely with the

screen facing in when not in use.

LCD monitor

POWER switch

LOCK button

Summary of Contents for ViewCam Slim VL-AX1S





























































































































Reviews: