Sharp UX-BA50 Operation Manual Download Page 79

Page: 79 / 123

Using TEL Mode

4. Receiving

When the fax machine rings, pick up

the handset.

If you hear a fax tone, wait until

the display shows RECEIVING and
then replace the handset.

If the other party first speaks with you

and then wants to send a fax, press

after speaking. (Press before

the sender presses their Start key.)

•

When RECEIVING appears in the
display, hang up.

START/

MEMORY

Answering with the fax’s handset

Important:

If a document is loaded in the machine’s feeder, remove it before

performing the steps below. (Fax reception is not possible when a document
is in the feeder.)

If RECEIVING does not appear (or if you have set the Fax

Signal Receive setting to NO), press

to begin reception.

START/

MEMORY

Beep

RECEIVING

START/

MEMORY

all.book Page 77 Tuesday, August 3, 2004 11:08 AM

Summary of Contents for UX-BA50




























































































































Search results

Summary of Contents for UX-BA50

Reviews:

Related manuals for UX-BA50

Brands by name

Popular brands

Sharp UX-BA50, Operation Manual

Search results

Summary of Contents for UX-BA50

Reviews:

Related manuals for UX-BA50

Brands by name

Popular brands