Sharp UX-BA50 Operation Manual Download Page 38

Page: 38 / 123

Operating the Answering Machine

To listen to the outgoing message

To listen to the outgoing message, follow Steps 1 and 2 of the above

procedure and then press

. Note that the general outgoing message

cannot be erased. If you need to change it, simply repeat the recording
procedure.

Operating the Answering Machine

Activating the answering machine

To turn on the answering machine so that callers can leave messages, press

until the arrow in the display points to A.M.

PLAY

RECEPTION

Press

and speak into the handset to record a message.

•

The outgoing message can be up to 60 seconds long. While recording, the
display will show the time left to record.

When finished, replace the handset or press

START/

MEMORY

♦

The outgoing message will play (you can stop playback by pressing

♦

It will not be possible to set the reception mode to A.M. if an outgoing
message has not been recorded.

FAX

TEL

A.M.

TEL/FAX

RECEPTION

all.book Page 36 Tuesday, August 3, 2004 11:08 AM

Summary of Contents for UX-BA50




























































































































Search results

Summary of Contents for UX-BA50

Reviews:

Related manuals for UX-BA50

Brands by name

Popular brands

Sharp UX-BA50, Operation Manual

Search results

Summary of Contents for UX-BA50

Reviews:

Related manuals for UX-BA50

Brands by name

Popular brands