Sharp UX-BA50 Operation Manual Download Page 67

Page: 67 / 123

Sending a Fax by Automatic Dialling

3. Sen

Sending a fax by Direct Keypad Dialling

You can also enter a full number with the number keys and then press the

key to begin dialling. You can use this method to dial a full number

when you don't need to speak to the other party before faxing.

START/

MEMORY

Load the document(s).

•

If desired, press

to set the

resolution and/or contrast.

Enter the number of the receiving machine by pressing the number
keys.

•

If a pause is required between any of the digits to access a special service

or an outside line, press

. The pause will appear as a hyphen (two

seconds per pause). Several pauses can be entered in a row.

Check the display. If the number of the receiving machine shown is

correct, press

•

If the number is not correct, press

to backspace and clear one digit at

a time, and then re-enter the correct digit(s).

RESO.

START/

MEMORY

READY TO SEND

all.book Page 65 Tuesday, August 3, 2004 11:08 AM

Summary of Contents for UX-BA50




























































































































Search results

Summary of Contents for UX-BA50

Reviews:

Related manuals for UX-BA50

Brands by name

Popular brands

Sharp UX-BA50, Operation Manual

Search results

Summary of Contents for UX-BA50

Reviews:

Related manuals for UX-BA50

Brands by name

Popular brands