manualshive.com logo in svg

Sharp MX-FXX1, Service Manual

Share
Download
Sharp MX-FXX1 Service Manual Download Page 67

MXFXX1  TROUBLE CODE  6 – 3

51

PASS # NG

In poling sending, the allow number is not matched. <Bulletin board>
In polling sending, the system number is not matched. <Bulletin board>

52

(No confidential function in 
remote party)

In confidential sending, the remote party does not have confidential function. <Send>
(Including other company's machines)
1)

The NSF signal has not "Confidential function" bit.

2)

The NSF is not a Sharp machine. 

53

(Confidential not received)

1)

In confidential sending, DCN is received for NSS. <Send>

54

(Confidential BOX NO NG)

1)

In confidential reception, a confidential box number which is not registered is specified.

55

(No relay function in 
remote party)

In relay command sending, the remote machine has no relay function. <Send>
(Including other company's machine)
1)

The NSF signal has not "Confidential function" bit.

2)

The NSF is not a Sharp machine.

56

NO REL RX

1)

In relay command sending, DCN is received for NSS. <Send>

2)

In relay command reception, a remote station number which is not registered is specified. <Receive>

3)

In F code relay broadcasting, an F code relay command is received.<Receive>

57

(Relay ID unmatched)

1)

In relay command reception, the relay ID does not match. <Receive>

58

REJECTED

In reception, data are sent from a remote machine of receive inhibit number. <Receive>
(Not rejected in the bulletin board send or the F code bulletin board send.)

59

RX NO F-CODE POLL

In F code polling (calling), the remote machine has no DIS bit 47 (polling function). <Polling>
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)<Polling>

60

NO F-CODE POLL

In F code polling (calling), DCN is received for SEP. <Polling>
In bulletin board, there is no send data for SEP. <Bulletin board>

61

RX POLL # NG

In bulletin board, the sub address (bulletin board number (SEP)) is not matched. <Bulletin board>

62

F POLL PASS # NG

In bulleting board, the pass code (PWD) is not matched. <Bulletin board>

63

NO F FUNC

In F code sending, the remote machine has no DIS bit 49 (sub address function). <Send>
(Check that the remote machine conforms to F code.)

64

NO F-CODE

In F code sending : <Send>
1)

DCN is received for SUB. --- Check the box number.

2)

DCN is received for SID. --- Check the box number and pass code.

In F code receiving : <Receive>
"F code relay broadcasting" or "F code confidential reception" is "Inhibited with soft SW."

67

F PASS # NG

In F code receiving, the pass code (SID) is not matched. <Receive>

68

BOX NO. NG

In F code reception, a box number which is not registered is specified. (SUB is not matched.) <Receive>

69

MEMORY OVER

Memory over in quick online sending <Send>

70

(JOB MEMORY OVER)

In PC-FAX reservation, the number of remote parties is exceeded. <Send>

71

NG71 XXXX *1

In PC-FAX reservation, data sent from PC includes some errors. <Send>

72

(NG72 XXXX) *1

In department management setting on the machine side:
• In reservation from PC-FAX or PC-Internet FAX, a department number which is not registered on the 

machine side is specified. <Send>

• In reservation from PC-FAX or PC-Internet FAX, the department number is not specified. <Send>

73

NG73 XXXX *1

In reservation from PC-FAX or PC-Internet FAX, the use quantity limit is exceeded. <Send>

74

NG74 XXXX *1

When reserving specified filing in document filing in PC-FAX or PC-Internet FAX;
• The pass-code for the folder is set on the machine side and the pass-code from PC-XXX does not match 

with it. <Send>

• The pass-code for the folder is set on the machine side and no pass-code is specified by PC-XXX. <Send>

75

NG75 XXXX *1

• Reservation cannot be made due to machine busy. (Reservation of PC-FAX cannot be accepted.)
• When "PC-FAX or PC-internet FAX send inhibit" is set on the machine side.

76

NG76 XXXX *1

Reserved with receive confirmation request in PC-Internet FAX, but the Internet FAX sender is not registered 
on the machine side. <Send>

77

NG77 XXXX *1

In reserving specified filing in PC-FAX or PC-Internet FAX, the machine has no filing function.

78

NG78 XXXX *1

The filing function is inhibited on the machine side when filing specification is reserved by PC-FAX or PC-
Internet FAX.

79

NG79 XXXX *1

An authentication error occurs when PC-FAX or PC-Internet FAX is reserved.

80

NG80 XXXX *1

NIC connect failure (network abnormality)
• Check for disconnection of cables.
• A network trouble (CE-XX) occurs.
• The port is set to DISABLE.
• Authentication of the POP server is failed when POP before SMTP is enabled.

81

NG REPORT

In Internet FAX send, reply of receive confirmation of the remote machine is not normal. (Including PC-Internet 
FAX). 
• Error of the disposition-modifier.
• The disposition modifier is not in an error, and the disposition type is other than displayed, dispatched, or 

processed.  

82

NO REPORT

In Internet FAX send, time-out occurs in waiting for receive confirmation from the remote machine. (Including 
PC-Internet FAX).
• In a case where send confirmation wait time-out time is other than 0, when send confirmation reply from an 

Internet FAX destination is not received.

• Recalls of the set number of recalls are performed, but send confirmation reply from an internet AFX 

destination is not received.

83

NG LIMIT

In E-mail/FTP, Internet FAX send, the send data size exceeds the upper limit of send data.

84

REJECTED

In e-mail receive, a sender is registered in receive reject address/domain. <Receive>

Report code 

(Communication 

result)

Display in the column of 

result

Content of communication interruption

Summary of Contents for MX-FXX1

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands