Sharp MX-FXX1, Service Manual

Page: 18 / 80

MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 9
5) When [YES] button is pressed, it is highlighted and the soft SW
corresponding to the country code is initialized.
* During clearing the FAX-related soft SW, [EXECUTE] and
[YES] buttons are highlighted.
6) After completion of initialization of the soft SW, [EXECUTE],
[YES], and [NO] buttons become inactive.
* When [CA] key is pressed after completion of initialization of
the soft SW, the whole machine is reset.
Operation/Procedure (Shifting to the country page)
* When [DEST CODE] button is pressed on the initial screen, the
display is shifted to the country code list screen.
Use [
↑
] [
↓
] buttons to select the country select page.
When the table item is the top (last)item, [
↑
] [
↓
] buttons gray out.
When [
↑
] [
↓
] buttons gray out, they are disabled.
* Press [BACK] button to return to the entry screen.
<Country code list>
Initial screen
Country code list screen
66-3
Purpose : Operation test/Check
Function (Purpose) : Used to execute the read/write check of
EEPROM on the MODEM controller,
SDRAM, SRAM on the MFP controller, and
flash ROM, and to display the results.
Section : FAX
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 66-03, the following
screen is displayed.
* Use [
↑
] [
↓
] buttons to select the country select page. (The
highlighted section of the set value is switched and dis-
played on the set setting area.)
When [
↑
] [
↓
] buttons gray out, they are disabled.
2) When the memory check item button is selected, the display is
shifted to the memory check screen.
* Only one memory check item can be selected.
3) When [EXECUTE] button is pressed, it is highlighted and the
memory check of the selected item is started.
* When [EXECUTE] button is pressed again during memory
check, the operation is interrupted. (The display shows the
status immediately before pressing [EXECUTE] button.)
When [EXECUTE] button is pressed after interrupting the
operation, memory check is resumed.
4) After completion of memory check, [EXECUTE] button returns
to the normal display and the result of memory check is dis-
played.
* For the memory which is not installed, [NO CHECK] is dis-
played.
* In the case of [REPEAT] check, the following display is made for
every execution.
CHECKING 0001
CHECKING 0002
CHECKING 0003
:
:
The number of times is displayed in 4-digit decimal numbers.
When the number exceeds 9999, it becomes 0000
Check is repeated until [EXECUTE] is pressed or [NG] occurs.
Memory check status
Check item
JAPAN 00000000
U.S.A. 10110101
AUSTRALIA 00001001
U.K. 10110100
FRANCE 00111101
GERMANY 00000100
SWEDEN 10100101
NEWZEALAND 01111110
CHINA 00100110
SINGAPORE 10011100
TW 11111110
OTHER1 11111101
OTHER2 11111100
OTHER3 11111011
FINLAND 00111100
NORWAY 10000010
DENMARK 00110001
NETHERLANDS 01111011
ITALY 01011001
SWITZERLAND 10100110
AUSTRIA 00001010
INDONESIA 01010100
THAILAND 10101001
MALAYSIA 01101100
INDIA 01010011
PHILIPPINES 10001001
HONGKONG 01010000
RUSSIA 10111000
SOUTHAFRICA 10011111
SPAIN 10100000
PORTUGUESE 10001011
LUXEMBURG 01101001
BELGIUM 00001111
CZECH 00101110
HUNGARY 01010001
GREECE 01000110
POLAND 10001010
SIMULATION NO.66-02
TEST
FAX SOFT SW.CLEAR(WITH ADJUSTMENT VALUE). CHINA
CLOSE
PRESENT 00000000
㧦
㧦
NEW 㧦 SET
EXECUTE
DEST CODE
ARE YOU SURE?
YES NO
NO CHECK No check
CHECKING During checking
OK Check complete OK
NG A## Check complete NG Error occurring address or data
line is displayed for each item.
Check memory item Remark
1 All Memory Device Check (Once) All the items are checked
once.
2 MFP SRAM (Once) Check only once
3 MFP SRAM (Repeat) Repeat check
4 MFP FLASH + OP.FLASH (Once) Check only once
SIMULATION NO.66-02
TEST
FAX SOFT SWITCH CLEAR
CLOSE
JAPAN
:00000000
U.S.A
:10110101
AUSTRALIA
:00001001
U.K
:10110100
FRANCE
:00111101
GERMANY
:00000100
SWEDEN
:10100101
NEWZELAND
:01111110
CHINA
:00100110
SINGAPORE
:10011100
TW
:11111110
OTHER1
:11111101
BACK