Sharp MX-C250F Technical Handy Manual Download

Page: 9 / 65

SHARP

INITIAL SETUP

HALF TONE COLOUR CALIBRATION

Sim 46-24

Colour Balance Adjustment/Calibration

[MX-C250/300 only].

Sim 46-74

Colour Balance Adjustment/Calibration [MX-C301W only].

COPY IMAGE QUALITY

Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.

If NG, perform the following adjustments as required:-

Sim 46-01

Copy Density Adjust. (Colour).

Sim 46-02

Copy Density Adjust. (B/W).

Sim 46-09

SPF Copy Density Adjust.

Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc).:

Sim 48-01

Magnification Adjustment (OC & SPF).

Sim 50-01

Lead/Rear Edge, Loss & Void Adjust.

Sim 50-12

OC & SPF Off Centre Adjust.

PRINT IMAGE QUALITY

Check Image Quality (Print Mode) – Density.

Sim 64-05

PCL Density Test Page.

Sim 64-06

PS Density Test Page.

FACSIMILE

Sim 66-02

Fax SW Setting (Destination).

Sim 66-10

Fax Memory Clear.

OPTION CONFIGURATION

EXTERNAL ACCOUNTING MODULE – MX-AMX3

Sim 55-03

Auto clear function before Copy job execution:-

SSW 1-5

0 = Disable, 1 = Enable.

Sim 55-03

USB Card Reader detection control:-

SSW 6-8

0 = Disable, 1 = Enable.

Sim 55-03

Continuous print mode (job queuing for OSA):-

SSW 24-7

0 = Disable, 1 = Enable.

Summary of Contents for MX-C250F


































































Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands

Sharp MX-C250F, Technical Handy Manual

Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands