Sharp MX-C250F Technical Handy Manual Download

Page: 19 / 65

SHARP

ELECTRICAL

High Voltage Settings

The adjustment value of each colour mode is specified on the information label attached to the
High Voltage Power PWB.

Using Simulation 8-01 (DV Bias Setting) & Sim 8-02 (MC Grid Bias Setting), enter the values
specified, especially after U2 trouble:-

DV BIAS VOLTAGE – SIMULATION 08-01

Item

Mode

Item/Display

Adjustment

Range

Middle Speed

DV Bias Voltage

M_DVB_K

0-600

M_DVB_C

M_DVB_M

M_DVB_Y

Low Speed

DV Bias Voltage

L_DVB_K
L_DVB_C

L_DVB_M

L_DVB_Y

MAIN CHARGE GRID VOLTAGE – SIMULATION 08-02

Item

Mode

Item/Display

Adjustment

Range

Middle Speed

MC Grid Voltage

M_GB_K

150-850

M_GB_C

M_GB_M

M_GB_Y

Low Speed

MC Grid Voltage

L_GB_K
L_GB_C

L_GB_M

L_GB_Y

Note:

The adjustment value may differ depending on the high voltage power PWB.

As the adjustment value label is attached on the high voltage PWB, the Main PWB must be

removed in order to check the adjustment value.

Summary of Contents for MX-C250F


































































Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands

Sharp MX-C250F, Technical Handy Manual

Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands