Sharp MX-C250F Technical Handy Manual Download

Page: 11 / 65

SHARP

COLOUR CALIBRATION

MX-C250F, MX-C300W

Note:

When adjusting colour balance before or after routine maintenance, always use the

recommended paper (Mondi 90gsm or equivalent) for optimum image quality.

Manual Colour Calibration [COPY MODE]

HIGH DENSITY PROCESS CONTROL:

[Execute]

Sim 44-06

ENGINE COLOUR BALANCE ADJUSTMENT:

Sim 46-24

[Auto Adjustment]

Place printed test pattern onto OC glass.

MANUAL COLOUR DENSITY ADJUSTMENT:

Sim 46-21

[for Engine]

Adjust CMYK (17 points) for Copy Mode.

SET HALF TONE PROCESS CONTROL TARGET

[Execute]

Sim 44-21

HALF TONE PROCESS CONTROL EXECUTION

[Execute]

Sim 44-26

Manual Colour Calibration [PRINTER MODE]

Prior to checking or adjusting Printer Colour Balance Adjustment, ensure to execute Engine Colour
Balance Adjustment (as described above):-

MANUAL COLOUR DENSITY ADJUSTMENT:

Sim 67-25

[for Printer]

Adjust CMYK (17 points) for Copy & Printer Modes.

PRINTER DENSITY CHECK:

Sim 64-05

[PCL Printer]

Sim 64-06

[PS Printer]

Summary of Contents for MX-C250F


































































Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands

Sharp MX-C250F, Technical Handy Manual

Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands