Sharp MX-C250F Technical Handy Manual Download Page 60

Page: 60 / 65

REPAIR HINTS

SHARP

SPECIFICATION

Model

Symptom

Advice

MX-C250F

MX-C300W

Is it possible setup Inbound Routing

using Email destination addresses?

MX-C250/300 series only supports Network Folder

destinations when configuring Inbound Routing.

Can the Ethernet speed of the

MXC250/300 series be fixed?

Upgrade the MFP Firmware to Special ROM version

02.05.E1.f0

After reboot, Log in using Admin Mode via the Web page.

Under Network Setup > General Configuration, set Auto-

Negotiation, Speed and Duplex Modes accordingly

TROUBLE CODES

MX-C250F

MX-C300W

C1-10 trouble after recovering from

Power Save mode

Upgrade the MFP Firmware to v02.00.E1 (or higher).

H3-00 trouble

This may be caused by static electricity discharged due to

poor earthing of the fusing separation plate.

Add fusing separation earth spring [MSPRT0655QSZZ ],

screw [XEBS730P12000] & washer [XWHS730-05080] to

the rear side of the fusing unit.

L4-06

Check to see if the wire harness for the primary transfer

positioning sensors is routed correctly and is not

clamped/pinched between the high voltage TC holder and

the chassis.

NG Example

GENERAL / MISC

MX-C301W

SIM24-6 - SIM24-15 are missing?

To avoid counters that can be cleared accidentally

(affecting End User Counter data/information), these

Simulations are now hidden as default.

MX-C250F

MX-C300W

Double sheet feeding from the SPF

The SPF separation pad has been upgraded to the same

type used on MX-C301W. Replace with PSHEZ0837QSZZ

Summary of Contents for MX-C250F


































































Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands

Sharp MX-C250F, Technical Handy Manual

Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands