Sharp MX-C250F Technical Handy Manual Download Page 55

Page: 55 / 65

SHARP

TROUBLE CODES

LSU thermistor trouble

K drum phase sensor trouble

CL drum phase sensor trouble

Temperature/humidity sensor trouble

Toner supply operation trouble (K)

Toner supply operation trouble (C)

Toner supply operation trouble (M)

Toner supply operation trouble (Y)

Improper toner cartridge detection (K)

Improper toner cartridge detection (C)

Improper toner cartridge detection (M)

Improper toner cartridge detection (Y)

Toner cartridge CRUM error (K)

Toner cartridge CRUM error (C)

Toner cartridge CRUM error (M)

Toner cartridge CRUM error (Y)

Image density registration sensor trouble

High density process control high voltage
error (K)

[MX-C301W]

High density process control high voltage
error (C)

[MX-C301W]

High density process control high voltage
error (M)

[MX-C301W]

High density process control high voltage
error (Y)

[MX-C301W]

Paper feed tray 2 lift up trouble

ICU-Fax communication trouble (ICU)

Fax EEPROM read/write error

[MX-C301W]

Fax modem operation trouble.

LIU & Fax soft switch error (combination)

Access error to 1-chip on Fax board

[MX-C301W]

Fax Pwb compatibility trouble

[MX-C301W]

Improper Fax & Destination information

[MX-C301W]

Communication error between MFP and
printer section when booting

[MX-C301W]

Thermistor open trouble (TH_UM_AD2).

Thermistor open trouble (TH_US).

Compensation Thermistor open trouble
(TH_UM_AD1 or TH_UM_CS)

Fuser high temperature trouble (TH_UM
or TH_UM_CS).

Sub thermistor fusing section high
temperature (TH_US).

Fuser low temperature (TH_UM_AD1 or
TH_UM_CS)

5 continuous (POD1 not reach) jams

Fuser low temperature recovery error
(TH_UM_CS)

Scanner feed trouble.

Scanner return trouble.

Paper feed motor trouble

Fusing motor trouble

DV motor trouble K

Transfer unit lift trouble

[MX-C301W]

Drum motor lock trouble

Power source cooling fan trouble

LSU fan trouble

Fusing cooling fan trouble

Ozone fan motor 1 trouble

Power source cooling fan 2 trouble

[MX-C301W]

Power source cooling fan 3 trouble

[MX-C301W]

Polygon motor trouble (LSU)

Summary of Contents for MX-C250F


































































Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands

Sharp MX-C250F, Technical Handy Manual

Search results

Summary of Contents for MX-C250F

Reviews:

Related manuals for MX-C250F

Brands by name

Popular brands