Sharp MX-5111N Technical Handy Manual Download Page 50

Page: 50 / 68

TROUBLE CODES

SHARP

Upper thermistor open (TH_UM_AD2).

Lower thermistor open (TH_LM).

Sub thermistor open (TH_US).

Compensation thermistor open trouble
(TH_UM_AD1)

Fuser high temperature (TH_UM).

Fuser high temperature (TH_LM).

Sub thermistor fusing section high
temperature (TH_US).

Fuser low temperature (TH_UM_AD2)

Fuser low temperature (TH_LM)

Sub thermistor fusing section low
temperature (TH_US)

5 continuous (POD1 not reach) jams

Fuser low temperature recovery error
(TH_UM_AD2)

Fuser low temperature recovery error
(TH_LM)

Mirror feed trouble.

Mirror return trouble.

Paper feed motor lock trouble

Fusing motor trouble

DV motor trouble K

DV motor trouble CMY

Transfer unit lift trouble

Transfer belt motor trouble

Shift motor trouble

Fusing pressure release trouble.

MFP fan motor trouble

Paper exit cooling fan trouble

Power source cooling fan trouble

LSU cooling fan trouble

Fusing cooling fan trouble

Toner cooling fan trouble

Process fan trouble

Rear cooling fan trouble

Ozone exhaust fan trouble

Polygon motor trouble (LSU)

No Full wave signal

Full wave signal error

MFP PWB communication trouble

Personal counter not installed

Battery trouble.

MFP EEPROM read/write error

HDD internal authentication database
table error.

SRAM user authentication check sum
error

MFP PWB EEPROM check sum error.

Serial number discrepancy (ICU – PCU)

SD card error.

HDD system storage data area error

Machine adjustment data (system
storage area) error

HDD user authentication data check sum
error

Watermark check error.

SCU PWB EEPROM read/write error.

SCU PWB EEPROM check sum error.

PCU PWB EEPROM read/write error.

PCU PWB EEPROM check sum error

Summary of Contents for MX-5111N





































































Search results

Summary of Contents for MX-5111N

Reviews:

Related manuals for MX-5111N

Brands by name

Popular brands

Sharp MX-5111N, Technical Handy Manual

Search results

Summary of Contents for MX-5111N

Reviews:

Related manuals for MX-5111N

Brands by name

Popular brands