Sharp MX-5111N Technical Handy Manual Download Page 9

Page: 9 / 68

SHARP

INITIAL SETUP

PRINT IMAGE POSITION & MAGNIFICATION

Automatic Adjustment:-

Sim 50-28

BK MAG ADJ (Main Scan Mag).

SETUP/PRINT ADJ (Lead, Offset or All).

Manual Adjustment:-

Sim 50-10

BK MAG (inside dimension) to 240mm.

Sim 50-10

Image Off Centre Adjustment.

Sim 50-05

Printer Lead Edge & Void Adjust.

IMAGE SKEW & COLOUR REGISTRATION

Sim 61-04

Image Skew Adjustment (Black):-

Select A3 Paper

Sim 50-22

Colour Registration/Skew & OPC Drum Phase Adjustment:-

Check/Adjust SKEW (CMY) so value is Close to 0 as possible

(Result=OK)

COLOUR CALIBRATION

Sim 46-74

Engine & Printer Colour Calibration:-

Select

FACTORY

Mode.

COPY IMAGE QUALITY

Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.

If NG, perform the following adjustments as required:-

Sim 46-01

Copy Density Adjust. (Colour).

Sim 46-02

Copy Density Adjust. (B/W).

Sim 46-09

DSPF Copy Density Adjust.

Sim 50-28

OC ADJUST (Lead, Offset & Mag).

SPF ADJ:(Lead, Offset & Sub scan).

Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc):-

Sim 48-01

Magnification Adjustment (OC & SPF).

Sim 50-01

Lead/Rear Edge, Loss & Void Adjust.

Sim 50-12

OC & SPF Off Centre Adjust.

PRINT IMAGE QUALITY

Check Image Quality (Print Mode) – Density.

Sim 64-05

PCL Density Test Page.

Sim 64-06

PS Density Test Page [MX-PK11 only].

Summary of Contents for MX-5111N





































































Search results

Summary of Contents for MX-5111N

Reviews:

Related manuals for MX-5111N

Brands by name

Popular brands

Sharp MX-5111N, Technical Handy Manual

Search results

Summary of Contents for MX-5111N

Reviews:

Related manuals for MX-5111N

Brands by name

Popular brands