background image

 

General

 

Please ensure that the equipment is positioned in a well 
ventilated area and ensure that there is at least 4” (10 
cm) of free space along the sides, top and back of the 
equipment.

PORTABLE MUSIC BOOMBOX GX-BT9

REMOTE 

SENSOR

4” (10 cm)

4” (10 cm)

4” (10 cm)

4” (10 cm)

  Use the unit on a firm, level surface free from vibration.

  Place the unit at least 12” (30 cm) away from any CRT 

TV to avoid color variations across the TV screen. If the 

variations persist, move the unit further away from the 

TV. LCD TV is not prone to such variation.

  Keep the unit away from direct sunlight, strong magnetic 

fields, excessive dust, humidity and electronic/electrical 

equipment  (home  computers,  facsimiles,  etc.)  which 

generate electrical noise.

  Do not place anything on top of the unit.

  Do not expose the unit to moisture, to temperatures higher 

than 140°F (60°C) or to extremely low temperatures.

  If your system does not work properly, disconnect the AC 

power cord from the AC outlet. Plug the AC power cord 

back in, and then turn on your system.

  In case of an electrical storm, unplug the unit for safety.

  Hold  the  AC  power  plug  by  the  head  when  removing 

it  from  the AC  outlet,  as  pulling  the  cord  can  damage 

internal wires.

  The AC power plug is used as a disconnect device and 

shall always remain readily operable.

  

Do not remove the outer cover, as this may result 

in electric shock. Refer internal service to your local 

SHARP service  facility.

  This unit should only be used within the range of 41°F 

- 95°F (5°C - 35°C).

  Do not lift the unit by holding left or right side panel, it may 

cause speaker diaphragm or unit damage and broken.

Warning:

The voltage used must be the same as that specified on 

this unit. Using this product with a higher voltage other than 

that which is  specified is dangerous and may result in a fire 

or other type of accident causing damage. SHARP will not 

be held responsible for any damage resulting from use of 

this unit with a voltage other than that which is specified.

 

Volume control

The sound level at a given volume setting depends on 

speaker  efficiency,  location,  and  various  other  factors. 

It  is  advisable  to  avoid  exposure  to  high  volume  levels, 

which occurs while turning the unit on with the volume 

control setting up high, or while continually listening at high 

volumes. Excessive sound pressure from earphones and 

headphones can cause hearing loss.

Precautions

E-5

Summary of Contents for GX-BT9























Reviews: