Sharp FO-DC635U Service Manual Download Page 56

Page: 56 / 166

FO-DC635U

2 – 37

SW70 No. 2 Reserved

Set to "0".

SW70 No. 3 Reserved

Set to "1".

SW70 No. 4 ~ No. 7 Reserved

Set to "0".

SW70 No. 8 Reserved

Set to "1".

SW71 No. 1, No. 2 The default resolution for copying

In case of copying without pressing the RESOLUTION key, resolution
will be super fine.

SW71 No. 3 Reserved

Set to "0".

SW71 No. 4 Reserved

Set to "1".

SW71 No. 5 Reserved

Set to "0".

SW71 No. 6, No. 7 Picture quality priority mode

Used to set the transmission mode which is automatically selected
when the MODE key is not pressed. In the copy mode, however, the
fine mode is automatically selected unless the MODE key is manually
set to another mode.

SW71 No. 8 Reserved

Set to "0".

SW72 No. 1 Reserved

Set to "1".

SW72 No. 2 Reserved

Set to "0".

SW72 No. 3 Reserved

Set to "1".

SW72 No. 4 ~ No. 8 Reserved

Set to "0".

SW73 No. 1 ~ No. 5 Reserved

Set to "0".

SW73 No. 6 ~ No. 8 Data reduction (Except notation: Setting pro-
hibition)

Reduction ratio of receiving is set.

It can be changed even in the optional mode.

To set printing reduction rate of received images.

SW74 No. 1 Automatic printing of activity report

This soft switch is used to select; whether or not to produce the activity
report when the memory is full (about 50 items). An activity report can
be produced when the following key entry command is made.

"FUNC", "2", "#", "START"

After producing the activity report, all the data in the memory will be
cleared.

When the switch function is set to "0" (NO), the data in memory will be
deleted from the oldest as it reaches the maximum memory capacity
(approx. 50 items).

SW74 No. 2 Print out of total time and total number of pages on
activity report

Used to make a choice of whether the total communication time and
pages are recorded in the activity report.

SW74 No. 3 Reserved

Set to "0".

SW74 No. 4 Department function

This model has the department audit feature, it has to be set to 1 to uti-
lize this feature.

SW74 No. 5 ~ No. 8 Department ID digit

Used to set the department ID digit number.

When set to "D", the number is "4".

SW75 No. 1 Copy protect switch

When this switch is set to “1”, copy is for bidden.

SW75 No. 2 Cut-off mode (when copy mode)

When in copy, if the scanned data is out of the range of recording, the
operator has one of the choices below using the switch.

SW75 No. 3 Scanning ratio in memory input

In the case of memory transmission, etc., only letter size (A4) docu-
ments can be stored in the memory. To input B4 documents into the
memory, therefore, the B4 documents must be reduced to letter size
(A4) or the both ends of the B4 documents will be cut off to input the
center letter-size (A4) portion. This switch provides the selection.

0: Reduced to A4 size and inputted.

1: Both ends are cut off and the center portion (A4 size) is inputted.

SW75 No. 4 Overseas communication mode selection function

When this switch is set to "1", the communication is Super G3 mode
can be turned off by pressing the "SPACE" key before sending opera-
tion, for the transmission set after that (including polling).

SW75 No. 5 Reserved

Set to "0".

SW75 No. 6 ~ No. 8 Reduce ratio when copy mode (Except nota-
tion: Setting prohibition)

Reduction ratio of copying is set.

It can changed even in the optional mode.

SW76 No. 1, No. 2 Reserved

Set to "0".

SW76 No. 3, No. 4 Density adjustment (when Fine/STD mode)

This is used for density adjustment in fine/standard mode. Adjust the
density according to that of frequently used original.

Set to "Dark" for darker reading (either in the auto or the dark mode) of
light original. Set to "Light" for lighter reading (either in the auto or the
dark mode) of dark original.

Set to "Dark only in dark mode" for darker reading only in the dark
mode.

SW76 No. 5, No. 6 Density adjustment (when half-tone mode)

This is used for density adjustment in the half tone. Setting procedures
are the same as SW46 No. 3 and No. 4.

000:

Automatic

100:

100%

Except the above

100%

0: Continue:

Data is printed onto the next page with the last
20mm also printed at the beginning of the next
page.

1: Cut off: