Sharp FO-DC635U, Service Manual

Page: 48 / 166

FO-DC635U
2 – 29
4.2. Soft switch function description
SW1 No. 1 ~ No. 4 Recall interval
Choice is made for a recall interval for speed and rapid dial numbers.
Use a binary number to program this. If set to 0 accidentally, 1 will be
assumed.
SW1 No. 5 ~ No. 8 Recall times
Choice is made as to how many recall times should be made. Use a
binary number to program this.
SW2 No. 1 Dial mode
Switch the type according to the telephone circuit connected to the
facsimile.
0: TONE DIAL
1: PULSE DIAL
SW2 No. 2 Receive mode
Auto/manual receiving mode is set.
SW2 No. 3 ECM mode
Used to determine ECM mode function.
SW2 No. 4 Reserved
Set to "0".
SW2 No. 5 Polling security
This switch is employed to enable or disable the polling operation
using the ID code verification function, in order to prevent unautho-
rized polling operation.
SW2 No. 6 Auto cover sheet
When "1" (=YES) is selected, the cover sheet is automatically sent
after transmission of the original to notify the receiver of the number of
original sheets transmitted.
SW2 No. 7 JUNK-FAX function in manual reception
It is set whether JUNK-FAX is functioned in the manual receiving
mode or not.
SW2 No. 8 JUNK-FAX function
This function is used to receive data from a specific remote machine
(station registered in entry mode). It is the function that refused a
reception in the case that TSI of remote machine matched with fax
number of the station registered.
0: No
1: Yes
SW3 No. 1 ~ No. 4 Number of rings for auto-receive (0: No ring
receive)
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to nine rings
using a binary number. If the soft switch was set to 1, a direct connec-
tion is made to the facsimile. If it was set to 0 accidentally, receive ring
is set to 1. If it was above 9, receive rings are set to 9.
SW3 No. 5 ~ No. 8 Switch to auto-receive from manual receive (0:
No switch)
This setting allows machine to switch from manual to Auto Receive
mode. Setting this number to 0 forces machine to stay in Manual
receive mode. Entering the binary number 0 forces the machine to
remain in the manual answer mode. If a number between 1 and 9 is
entered, the machine will go into the answer mode after the given
number of rings. However, it can be used as an ordinary telephone if
the handset is taken off the hook before this programmed number is
finished. If entry of a number above 9 by accident, it will be set to 9. In
this case, it must be corrected to the proper number.
SW4 No. 1 ~ No. 3 Communication results printout
It is possible to obtain communication results after each transaction.
Normally, the switch is set (No. 1: 0, No. 2: 0, No. 3: 1) so that the
communication result is produced only a communication error is en-
countered. If No. 1 was set to 1, No. 2 was set to 1 and No. 3 was set
to 0, the communication result will be produced every time a communi-
cation is done, even if the communication was successful.
If No. 1 was set to 0, No. 2 to 1 and No. 3 to 0, the communication
result will be produced every transmission.
Setting No. 1 to 1 No. 2 to 0 and No. 3 to 0 will disable this function. No
transaction report will be printed.
If No. 1 was set to 0, No. 2 to 0 and No. 3 to 0, the communication
result is produced only after a timer and memory transmission or when
a communication error is encountered.
SW4 No. 4 Image addition function to the communication result
table (for memory transmission only)
Used to set addition of sending image to the communication result
table.
SW4 No. 5 Reserved
Set to "0".
SW4 No. 6 TEL billing code function
When set to "1", the TEL billing code function is enabled.
SW4 No. 7 Billing code position
When set to "1", the billing code is delivered before dialing the remote
number. When set to "0", the billing code is delivered after dialing.
SW4 No. 8 Multi-TTI feature
When this switch is set to "1", Multi TTI function is enabled.
SW5 No. 1 Time display format
When this switch is set to "0", time is displayed in 12-hour system.
When set to "1", 24-hour system.
SW5 No. 2 Date display format
Used to select date display/print formats.
0: DAY-Month-Year
1: Month-DAY-Year
SW5 No. 3 Header print
When it is set at 0, sender’s name, sending page number and so on
are automatically printed in the recording paper on the receiving side
during transmission. Thus, the sender can be known on the receiving
side.
0: Applied
1: Not applied
SW5 No. 4 Footer print
When set to "1", the date of reception, the sender machine No., and
the page No. are automatically recorded at the end of reception.
SW5 No. 5 DIS receive acknowledge during G3 transmission 1
When set to “0”, the unit proceeds to the next procedure after
DIS(NSF) is received once during transmission. If set to “1”, it follows
the setting of SW7 No.3.
SW5 No. 6 Substitute reception
Selection of substitute reception in the case of recording paper ex-
hausted or paper jam. If set to "NO", auto receive is disabled even
when the receive memory is ready to receive.
Substitute reception is not performed even during receive operation.