AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 24
Operation/procedure
1.
Select the speed (145mm/s, 122mm/s) with the 10-key.
2.
Press the [START] key.
The main motor rotates to start monitoring the toner density control
sensor. (3min operation)
After execution, interruption cannot be made for about 7 sec. ([CA] key
and [CUSTOM SETTINGS] key are disabled.)
* Even in toner end error, if there is no other error (including cover
open) after turning on the power, this simulation can be performed.
Operation/procedure
1) Open the cover with the power OFF.
2) Turn on the power. (Since the cover is open, the machine does not
perform initializing.)
3) Install the developing tank.
4) Execute the simulation.
5) Enter SIM 25-2. ([25]
→
[START] key
→
[2]
→
[START] key)
6) Open the cover just before starting the simulation.
7) Press the [START] key.
The main motor rotates. After stirring for 3 min, the toner density
control sensor value is sampled 16 times, and the average value is
stored.
When “EE-EU” or “EE-EL” after completion, an error display is shown.
Note: After completion of execution, be sure to press the [CA] key to
cancel the simulation.
[CRUM-related error cancel procedure]
• When “CRUM DEVICE ERROR” is displayed:
• “CRUM DATA ERROR”
• “DEVE UNIT NONE”
• “TONER UNIT NONE”
• “EU ERROR”
• “EL ERROR”
Operation/procedure
1.
Select the set value with the 10-key.
2.
Press the [START] key.
25
25-1
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of the main drive
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The toner
concentration sensor output can be monitored.)
Section
DRIVE
Item
Operation
25-2
Purpose
Setting
Function
(Purpose)
Used to make the initial setting of toner concentration
when replacing developer.
Section
Image process
(Photoconductor/Developing/Transfer/Cleaning)
Developer/Toner hopper
Error content:
Occurs in case of a communication error
between the machine and CRUM.
Cancel procedure: Reset with [CA] key and cancel with SIM 16.
Error content:
CRUM identification error, CRUM model error,
CRUM type error, CRUM destination error
Cancel procedure: Install the CRUM which is satisfactory with the
machine setup, reset with the [CA] key, and
execute SIM 25-2 again.
SIMULATION 25-1
Error content:
Occurs when the developing unit is not installed
in an AR model.
Cancel procedure: It returns to the state before execution of auto
developer adjustment. It is canceled by the
operations of Cover open
→
Developing unit
installation
→
Cover close. Therefore, developer
adjustment is started by pressing [START] key.
Error content:
Occurs when the CRUM is not installed in a DM
model.
Cancel procedure: It returns to the state before execution of auto
developer adjustment. It is canceled by the
operations of Cover open
→
CRUM installation
→
Cover close. Therefore, developer adjustment is
started by pressing [START] key.
Error content:
Occurs when the adjusted toner concentration
reference value is 179 or grater.
Cancel procedure: Reset with [CA] key and execute SIM 25-2 again.
Error content:
Occurs when the adjusted toner concentration
reference value is 77 or smaller.
Cancel procedure: Reset with [CA] key and execute SIM 25-2 again.
26
26-1
Purpose
Setting
Function
(Purpose)
Used to set whether the job separator is installed or
not. (Since this cannot be detected by hardware
detection, it is set in this simulation.)
Item
Specifications
Option
Set value
Connection option
0
None (default)
1
Job separator provided.
