11
Menu operations
H-Pos.:
Centres the image by moving it to the left
or right.
V-Pos.:
Centres the image by moving it up or down.
NOTE
Adjustments are stored separately for each input source.
Depending on the input signal type, a position setting may not
be available.
WSS (Wide Screen Signalling)
The “WSS” allows the TV to switch automatically among
the different picture size.
NOTE
Use “WIDE MODE” if an image does not switch to the
appropriate picture size. When the broadcast signal contains no
“WSS” information, the function will not work even if enabled.
4:3 Mode
The “WSS” signal has 4:3 auto-switching that allows you
to select between “Normal” and “Panorama”.
•
•
•
Input Label
You can label each input source with a custom
description.
Press
b
to select the desired input
source.
Go to “MENU” > “Setup” > “Input
Label”.
Press
a
/
b
/
c
/
d
to select each
character of the new name for the
input source, and then press
OK
.
Repeat step 3 until the label is fully
spelt out, and then press
OK
.
The label can be six characters or less.
If a label name is less than six characters, select
“END”, then press
OK
.
NOTE
You cannot change the label if the input source is “TV”.
Position
For adjusting a picture’s horizontal and vertical position.
1
2
3
4
•
•
•
HDMI Setup
HDMI (High-Definition Multimedia Interface) terminal
selection.
To watch an HDMI equipment image,
select “EXT1” or “EXT2” (the terminal
which you are using) from “INPUT
SOURCE” menu using
b
on the
remote control unit or TV.
Go to “MENU” > “Setup” > “HDMI
Setup”.
“HDMI Setup” is displayed only when “EXT1” or “EXT2”
is selected from the “INPUT SOURCE” menu.
Press
a
/
b
to select the desired item,
and then press
OK
.
Press
a
/
b
/
c
/
d
to select the desired
setting, and then press
OK
.
HDMI
Setup
items
Selectable
items
Description
Signal Type*
RGB/
YCbCr 4:4:4/
YCbCr 4:2:2
Select the video signal type from the
HDMI terminal.
Colour
Matrix*
ITU601/
ITU709
Select the internal colour space
conversion method when an RGB
signal is input.
Dynamic
Range*
Normal/
Enhanced
Select the signal amplitude range.
Usually, select “Normal”.
Auto View
Disable/Enable
Set whether or not to use “WIDE
MODE” based on signal recognition,
including an HDMI signal.
Audio
Select**
Digital/
Analogue
Select “Digital” for audio signal via the
HDMI terminal. Select “Analogue” for
audio signal via the AUDIO jack.
NOTE
Refer to your external equipment operation manual for the
signal type.
Items marked * may be greyed out (with
4
) depending on the
type of signal input from the external equipment.
Item marked ** is only available when “EXT1” is selected.
When “Analogue” is selected in “Audio Select” in the “HDMI
Setup” menu, an audio signal from a PC cannot be received.
Fine Sync.
Ordinarily, the TV automatically adjusts image positions
coming from PC (“Auto Sync.” function). In some cases,
however, manual adjustment is needed to optimise the
image.
1
2
•
3
4
•
•
•
•
Normal:
Normal range keeping 4:3 or 16:9 aspect
ratio.
Panorama:
Wide image without side bars.
WSS signal 4:3 screen
4:3 mode
“Panorama”
4:3 mode
“Normal”
H-Pos.:
Centres the image by moving it to the left
or right.
V-Pos.:
Centres the image by moving it up or down.
Clock:
Adjusts when the image flickers with vertical
stripes.
Phase:
Adjusts when characters have low contrast
or when the image flickers.
NOTE
If you need to adjust the image position, adjust the position
using your PC.
•
Item
Item
Item
