background image

Operating Instructions – MOVITRAC® LTP  

23

Installation

Electrical Installation

Key information 
on the control 
terminal 

• Maximum input voltage on any terminal: DC 30 V
• All outputs are short circuit proof
• Recommended potentiometer resistance: 1 k 

Ω

• Digital input response time < 8 ms

 

• Bipolar analog input response time < 16 ms. Resolution 

±

12-bit (0.025 %)

• Second analog input response time < 16ms. Reso11-bit (0.05 %)
• Analog / digital output response time < 16ms. Resolution  8-bit (0.25 %)

5.2.5

RJ11 Communication socket

The RJ11 communication socket can be used to set up a RS-485 communication to the
PC via UWS11A.
With MOVITRAC

®

 LTP units it is possible to use this RJ11 connector to set up a

MODBUS communication network.

The internal bus works with 115 k Baud (bps). It can be used for drive-to-drive commu-
nication. In this case, up to 63 drives can communicate.
The MODBUS RTU works between 9,6 and 115 k Baud (bps). It can be used to com-
municate directly with an external PLC or with a fieldbus gateway. In this case, up to 63
drives can be controlled via bus communication.

57406AXX

[1]

RS-485– / MODBUS 

1)

 

1) The bit format is fixed as: 1 start bit, 8 data bits, 1 stop bit, no parity

[2]

RS-485+ / internal bu

1)

[3]

RS-485– / internal bus 

1)

[4]

+24 V

[5]

0 V

[6]

RS-485+ / MODBUS 

1)

[2]
[3]

[4]

[5]
[6]

[1]

Summary of Contents for MOVITRAC LTP series

















































































Reviews: