SEW MOVIAXIS MX Operating Instructions Manual Download Page 194

Page: 194 / 212

194

Operating Instructions – MOVIAXIS® MX Multi-Axis Servo Inverter

Technical data for master module component

Technical Data

8.5

Technical data for master module component

MOVIAXIS

MXM

electronics data

Power consumption MOVIAXIS

MXM master module

MOVIAXIS

MX master module

MXM80A-...-000-00

1) Nameplate information

2) Unit

Size 1

Type

000

Supply voltage U

DC 24 V ± 25 % to EN 61131

Cross section and contacts (X5a)

COMBICON 5.08

One conductor per terminal: 0.20...2.5 mm

Two conductors per terminal: 0.25...1 mm

Cross section and contacts (X5b)

COMBICON 5.08

One conductor per terminal: 0.20...2.5 mm

Two conductors per terminal: 0.25...1 mm

Maximum outer diameter of the cable: 3.5 mm.

Recommended connector: MSTB 2.5/4-ST-5.08 BK (Phoenix)

(COMBICON 5.08 with front-end cable output)

GENERAL INFORMATION

Weight

2.3

Dimensions:

300

254

Shield clamps

Shield clamps for control lines available

Maximum cable cross section that can be con-
nected to the shield clamp

10 mm (with sheath)

NOTES

For other technical data, refer to the manual
• MOVI-PLC

basic DHP11B Controller

• MOVI-PLC

advanced DH.41B Controller

Master module

Power

See technical data of the integrated card. Due to the efficiency of
85 % of the integrated switched-mode power supply unit, the
power consumption of the integrated card must be multiplied by
factor 1.2.

kVA

Summary of Contents for MOVIAXIS MX





















































































































































































































Search results

Summary of Contents for MOVIAXIS MX

Reviews:

Brands by name

Popular brands

SEW MOVIAXIS MX, Operating Instructions Manual

Search results

Summary of Contents for MOVIAXIS MX

Reviews:

Brands by name

Popular brands