manualshive.com logo in svg

SEW MOVIAXIS MX, Operating Instructions Manual

Share
Download
SEW MOVIAXIS MX Operating Instructions Manual Download Page 137

Operating Instructions – MOVIAXIS® MX Multi-Axis Servo Inverter 

137

5

MOVIAXIS® startup - Single-motor operation

Startup

Application and system limits

The application and machine limit values refer to the set user-specified units, see figure
89. The user-specified units selected previously are shown in the illustration and cannot
be altered. 
The fields on the right refer to the download value in the axis, converted to the user-
specified unit. The fields on the left are calculated default values.
The following values are the basis for the basic configuration and the delivery status:

11813aen

Figure 90: Application and system limits menu

Variables

Limit values

System limit values (machine limit values)

VmaxSys

10000 1/min, corresponds to the maximum speed possible in the axis module

a_maxSys

3000 1/(min 

×

 s) acceleration ramp

b_maxSys

3000 1/(min 

×

 s) deceleration ramp

Application limit values

VmaxApp

10000 1/min, corresponds to the maximum speed possible in the axis module

a_maxApp

3000 1/(min 

×

 s) acceleration ramp

b_maxApp

3000 1/(min 

×

 s) deceleration ramp

Emergency stop deceleration

b_maxAppNotStop

3000 1/(min 

×

 s) deceleration ramp, emergency stop ramp is mainly used for 

error response.

0

0

I

Summary of Contents for MOVIAXIS MX





















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands