manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX25A Series, Manual, Page: 56 / 72

Share
Download
SEW-Eurodrive MOVI-C UHX25A Series Manual Download Page 56

5

Startup with EtherNet/IP™

Controlling the stations in test run

Manual – MOVI‑C

®

 CONTROLLER standard UHX25A

56

5.5

Controlling the stations in test run

During  successful  communication  between  PLC  and  the  MOVI‑C

®

  CONTROLLER,

process data words are transferred between the devices without faults.

5.5.1

Transferring process data words to the MOVI-C

®

 CONTROLLER

The process data exchange is monitored and controlled in Logix Designer with "Con-
troller Tags".

Proceed as follows:

ü

You  loaded  the  MOVISUITE

®

  project  to  the  MOVI‑C

®

  CONTROLLER  via  the

IEC Editor.

ü

The connection between the PLC and the MOVI‑C

®

 CONTROLLER is set up (the

PLC is in RUN mode).

1. Switch to the Logix Designer project.

2. In the "Controller Organizer", select the "Controller Tags" area.

ð

The right-hand screen pane displays the process data words that the PLC ex-
changes with the MOVI‑C

®

 CONTROLLER.

24519820043

ð

In  this  example,  these  process  output  data  words  are  sent  to  the
MOVI‑C

®

 CONTROLLER.

25800736/EN – 08/2018

Summary of Contents for MOVI-C UHX25A Series









































































Reviews:

No comments