manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX25A Series, Manual, Page: 47 / 72

Share
Download
SEW-Eurodrive MOVI-C UHX25A Series Manual Download Page 47

5

Startup with EtherNet/IP™

Configuration of the fieldbus stations

Manual – MOVI‑C

®

 CONTROLLER standard UHX25A

47

6. Select the number of process data words that you wish to use for communicating

with the subordinated slaves. Set the data format for the process data words. The
process data always contain 16 bits (data format INT).

24518069131

ð

In  this  example,  the  IP  address  of  the  MOVI‑C

®

  CONTROLLER  is:

192.168.10.40.  16  process  data  words  are  assigned  to  each  application  in-
verter module (slave of the MOVI‑C

®

 CONTROLLER) for communication. This

makes a total of 3 x 16 = 48 process data words.

7. If the direct integration of the device description file is not supported, set the follow-

ing connection parameters:

Assembly instance

Value

PO Data Exclusive Owner

120

PI Data Exclusive Owner

130

Listen Only

192

Input Only

193

8. Save the Logix Designer project.

25800736/EN – 08/2018

Summary of Contents for MOVI-C UHX25A Series









































































Reviews:

No comments