manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX25A Series, Manual, Page: 12 / 72

Share
Download
SEW-Eurodrive MOVI-C UHX25A Series Manual Download Page 12

2

Safety notes

Electrical installation

Manual – MOVI‑C

®

 CONTROLLER standard UHX25A

12

2.8

Electrical installation

Ensure that all of the required covers are correctly attached after carrying out the elec-
trical installation.

Make  sure  that  preventive  measures  and  protection  devices  comply  with  the  applic-
able regulations (e.g. EN 60204-1 or EN 61800-5-1).

2.8.1

Required preventive measure

Make sure that the product is correctly attached to the ground connection.

2.9

Bus systems

A  bus  system  makes  it  possible  to  adapt  electronic  drive  technology  components  to
the particulars of the machinery within wide limits. There is a risk that a change of pa-
rameters that cannot be detected externally may result in unexpected (but not uncon-
trolled) system behavior and may have a negative impact on operational safety, sys-
tem availability, or data security.

Ensure  that  unauthorized  access  is  prevented,  especially  with  respect  to  Ethernet-
based networked systems and engineering interfaces.

Use IT‑specific safety standards to increase access protection to the ports. For a port
overview, refer to the respective technical data of the device in use.

25800736/EN – 08/2018

Summary of Contents for MOVI-C UHX25A Series









































































Reviews:

No comments