SEW-Eurodrive MOVI-C UHX25A Series Manual Download Page 35

Page: 35 / 72

Startup with EtherNet/IP™

Configuration of the EtherCAT®/SBusPLUS stations

Manual – MOVI‑C

CONTROLLER standard UHX25A

5.3

Configuration of the EtherCAT

/SBus

PLUS

stations

Configurati

on of the

EtherCAT®/

SBusPLUS

stations

In the project example, the following devices are EtherCAT

/SBus

PLUS

stations:

•

The MOVI-C

CONTROLLER serves as EtherCAT

/SBus

PLUS

master.

•

The application inverters serve as EtherCAT

/SBus

PLUS

slaves.

The configuration of the devices is performed in the MOVISUITE

engineering soft-

ware.

The EtherCAT

/SBus

PLUS

stations are configured in several process steps:

2. "Scanning the network for devices" (→

5.3.1

Establishing a connection between engineering PC and MOVI-C

CONTROLLER

To ensure that the engineering PC can communicate via the engineering interface
X80 with the MOVI‑C

CONTROLLER via Ethernet, both the devices must be connec-

ted in the same local network. For this purpose, the IP address parameters of the en-
gineering PC must be set to the local network.

INFORMATION

In delivery state, the engineering interface X80 of the MOVI-C

CONTROLLER has

the following IP address parameters: Standard IP address 192.168.10.4, subnet
mask 255.255.255.0

Proceed as follows:

1. Select the network settings in the Windows control panel.

2. Double-click on the adapter that is physically connected to the engineering inter-

face X80 of the MOVI‑C

CONTROLLER.

25800736/EN – 08/2018

Summary of Contents for MOVI-C UHX25A Series









































































Search results

Summary of Contents for MOVI-C UHX25A Series

Reviews:

SEW-Eurodrive MOVI-C UHX25A Series, Manual, Page: 35 / 72

Search results

Summary of Contents for MOVI-C UHX25A Series

Reviews: