manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX25A Series, Manual, Page: 18 / 72

Share
Download
SEW-Eurodrive MOVI-C UHX25A Series Manual Download Page 18

4

Installation notes

Mechanical installation

Manual – MOVI‑C

®

 CONTROLLER standard UHX25A

18

4

Installation notes

4.1

Mechanical installation

 CAUTION

Risk of injury to persons and damage to property.

Never install defective or damaged MOVI-C

®

 CONTROLLERs.

•

Before installation, check the device for external damage. Replace any damaged
device.

4.1.1

Minimum clearance and mounting position

MOVI‑C

®

  CONTROLLER  is  installed  in  the  control  cabinet.  Observe  the  following  for

installation:

•

To ensure unobstructed cooling of the MOVI-C

®

 CONTROLLER, leave a minimum

clearance of 100 mm above and below the device's housing. Make sure air circula-
tion in the clearance is not impaired by cables or other installation equipment.

•

Ensure 

unobstructed 

cooling 

air 

supply 

and 

make 

sure 

that 

the

MOVI‑C

®

  CONTROLLER  is  not  exposed  to  the  warm  exhaust  air  from  other

devices.

•

There  is  no  need  for  clearance  at  the  sides  of  the  device.  You  may  connect  the
MOVI‑C

®

 CONTROLLER and other devices (e.g. MOVIDRIVE

®

 modular) in series.

•

Install  the  devices  only  vertically.  You  must  not  install  them  horizontally,  tilted  or
upside down.

The MOVI-C

®

 CONTROLLER is mounted onto a mounting rail.

4.2

Electrical installation

 

INFORMATION

Installation with protective separation.

The device meets all requirements for protective separation of power and electronics
connections in accordance with EN 61800‑5‑1. The connected signal circuits have to
meet  the  requirements  according  to  SELV  (

S

afe 

E

xtremely 

L

ow 

V

oltage)  or  PELV

(

P

rotective 

E

xtra 

L

ow 

V

oltage) to ensure protective separation. The installation must

meet the requirements for protective separation.

25800736/EN – 08/2018

Summary of Contents for MOVI-C UHX25A Series









































































Reviews:

No comments