SEW-Eurodrive DFE32B PROFINET IO Manual Download Page 76

Page: 76 / 132

Manual – DFE32B Fieldbus Interface PROFINET IO

Structure of the PROFINET parameter channel

Parameterization via PROFIdrive Data Set 47

7.2.3

Addressing connected inverters

The structure of the DS47 data set defines an

axis

element. This element is used to

reach multi-axis drives that are operated via one PROFINET interface. The

axis

element

addresses one of the units connected via the PROFINET interface.

Addressing a
MOVIDRIVE

on the PROFINET

With the setting

Axis = 0

, the parameters of the MOVIDRIVE

B drive inverter are ac-

cessed. Since there are no drive units connected to the MOVIDRIVE

B, an access with

Axis > 0

is returned with an error code.

62210AXX

Read / Write

Record

Axis = 0

Cyclic OUT Data

Cyclic IN Data

PROFINET

PROFINET
Controller

Summary of Contents for DFE32B PROFINET IO





































































































































Search results

Summary of Contents for DFE32B PROFINET IO

Reviews:

Brands by name

Popular brands

SEW-Eurodrive DFE32B PROFINET IO, Manual

Search results

Summary of Contents for DFE32B PROFINET IO

Reviews:

Brands by name

Popular brands