SEW-Eurodrive DFE32B PROFINET IO Manual Download Page 12

Page: 12 / 132

Manual – DFE32B Fieldbus Interface PROFINET IO

Installing the DFE32B option card in MOVIDRIVE® MDX61B

Assembly and Installation Notes

This section contains information about assembly and installation of the DFE32B
PROFINET IO option card in the MOVIDRIVE

MDX61B, MOVITRAC

B and UOH11B

gateway housing.

4.1

Installing the DFE32B option card in MOVIDRIVE

MDX61B

INFORMATION

•

Only SEW-EURODRIVE engineers are allowed to install or remove option
cards for MOVIDRIVE

MDX61B size 0.

•

Users may only install or remove option cards for MOVIDRIVE

MDX61B siz-

es 1 to 6.

•

Plug the DFE33B PROFINET IO option card into the fieldbus slot [1].

•

Only use connectors and cables approved for PROFINET IO when cabling.

62179AXX

[1]

Summary of Contents for DFE32B PROFINET IO





































































































































Search results

Summary of Contents for DFE32B PROFINET IO

Reviews:

Brands by name

Popular brands

SEW-Eurodrive DFE32B PROFINET IO, Manual

Search results

Summary of Contents for DFE32B PROFINET IO

Reviews:

Brands by name

Popular brands