SEON DX-HD Maintenance And Troubleshooting Manual Download Page 29 | Manualshive

Page: 29 / 50

SEON DX-HD Maintenance And Troubleshooting Manual Download Page 29

Seon Maintenance and Troubleshooting Guide R004 29

Removing the Hard Drive

The DVR has a removable drive that is contained in a drive tray. A drive lock secures the
cartridge during operation. Use the drive key to lock and unlock the drive.

Important:

While the drive is hot swappable (the drive can be removed when the DVR is powered up),

do not remove the drive while the DVR is recording, as the video segment may not be recorded. Press
the STOP/TEMP PWR button before unlocking and removing the drive.

To remove the drive:

1. Insert the drive key.

2. Turn the drive key counter clockwise by

¼

turn until the drive lock is in the unlocked position.

3. To ensure all recording has stopped, wait until the HDD LED stops flashing.

CAUTION: Data Loss
Do not remove the drive until the red HDD activity indicator is OFF. Failure to do so may result in lost
data.

4. Gently pull out the drive.

«
...
27
28
29
30
31
...
»

Summary of Contents for DX-HD



















































Reviews:

No comments