SenTech STC-GE33OX User Manual Download Page 24

Page: 24 / 76

No.11S098-03

STC-GE33OX/GEC33OX
Users guide Rev. 1.03

3.2.3 Important design consideration of data timing and handling

In the design process of the video processing program, follow the below conditions of the data timings.

1) DIN (image data), LVALIN and FVALIN are activated at the rising edges of CLKIN as the data comes into the

user FPGA.

2) As the data sent back to the Sentech FPGA, add the delay equivalent to the process time in the user FPGA

on LVALIN and FVALIN.

3) As the data is sent back to the Sentech FPGA, DIN (image data), LVALIN and FVALIN must be activated at

the rising edges of CLKIN.

CLKIN: 36.81MHz

CLKIN

DIN [11:0]

LVALIN

FVALIN

CLKIN

DOUT [11:0]

LVALOUT

FVALOUT

Number of clock for

image processing

Number of clock for

image processing

Number of pixel in 1 horizontal

Fig. 5 The image data input timing to user configurable FPGA

Fig.6 The image data output timing form user configurable FPGA after image processing

Summary of Contents for STC-GE33OX













































































Search results

Summary of Contents for STC-GE33OX

Reviews:

Related manuals for STC-GE33OX

Brands by name

Popular brands

SenTech STC-GE33OX, User Manual

Search results

Summary of Contents for STC-GE33OX

Reviews:

Related manuals for STC-GE33OX

Brands by name

Popular brands