Sennheiser XS Wireless Instruction Manual Download

Page: 15 / 78

Operation

Checking the charge level during use

The status LED remains green during use as long as the rechargeable bat

tery has sufficient charge. The status LED begins flashing red and green in

alternation when the charge level falls below 15%. Once the charge level

falls below 5%, the status LED flashes only red.
In addition to the local charge level, the status LED on a transmitter or re

ceiver also provides information about the charge level of the connected

transmitter or receiver. This allows you to check the charge levels at any

time.

The charge level is below 15%.

The charge level of the

connected

transmitter/

receiver is below 15%.

The charge level is below 5%.

The charge level of the

connected

transmitter/

receiver is below 5%.

Summary of Contents for XS Wireless















































































Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands

Sennheiser XS Wireless, Instruction Manual

Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands