Sennheiser XS Wireless Instruction Manual Download

Page: 57 / 78

Operation

Connecting the receiver to the camera

►

▷

Plug the camera cable’s screw-on jack plug into the jack socket on the

receiver.

▷

Lock the jack plug by screwing down the coupling ring.
If the jack plug is not firmly locked, crackling noise can appear in the

audio signal.

▷

Insert the receiver into the hot shoe adapter.

▷

Slide the hot shoe adapter onto your camera.

▷

Plug the camera cable’s simple jack plug into the jack socket on your

camera.

Switching on the transmitter and receiver

►

▷

Briefly press the button on the transmitter and the button on the receiv

er.
The status LEDs indicate the charge level for four seconds.

▷

During these four seconds, check that the transmitter and receiver are

sufficiently charged.

> 75%

5% – 75%

< 5%

If the status LED remains red, you should charge the rechargeable bat

Summary of Contents for XS Wireless















































































Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands

Sennheiser XS Wireless, Instruction Manual

Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands