Sennheiser XS Wireless Instruction Manual Download

Page: 50 / 78

Operation

The status LEDs remain green once the transmitter and receiver are

connected. If the status LEDs do not remain green, either the charge

level is below 15% (see „Checking the charge level during use“) or the

transmitter and receiver are not paired (see „Pairing“).

Switching off the transmitter and receiver

►

▷

Press the button on the transmitter and the button on the receiver until

the status LEDs switch off.

Adjusting the input level on the camera

Once you have connected the receiver to the camera and switched it on,

you have to adjust the input level on the camera.

►

▷

If the camera has automatic gain control (AGC), you should disable this

function.

▷

Set the input level in the camera’s menu so that the audio signal does

not overload the input.

▷

During recording, regularly check the input level on the camera to make

sure that the audio signal is not overloading.

Summary of Contents for XS Wireless















































































Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands

Sennheiser XS Wireless, Instruction Manual

Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands