Sennheiser XS Wireless Instruction Manual Download

Page: 26 / 78

Operation

Holding the microphone

►

▷

Grip the microphone only by the handle.

▷

Hold the microphone 5 to 10 cm in front of your mouth.

▷

Do not grab the transmitter. The range may decrease if the transmitter

is covered.

▷

Do not touch the microphone basket. The sound may be distorted if the

microphone basket is covered.

Switching on the transmitter and receiver

►

▷

Briefly press the button on the transmitter and the button on the receiv

er.
The status LEDs indicate the charge level for four seconds.

▷

During these four seconds, check that the transmitter and receiver are

sufficiently charged.

> 75%

5% – 75%

< 5%

If the status LED remains red, you should charge the rechargeable bat

tery first. If the status LED flashes red, the charge level is too low. You

have to charge the rechargeable battery first (see „Charging the re

chargeable battery“).
After four seconds, the status LED starts flashing green. The flashing

indicates that a wireless connection is being established.

Summary of Contents for XS Wireless















































































Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands

Sennheiser XS Wireless, Instruction Manual

Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands