Sennheiser XS Wireless Instruction Manual Download

Page: 77 / 78

Operation

Charging the rechargeable battery

To minimize charging time and monitor the charging status the transmitter

or receiver should be switched off before you charge the battery.
However the transmitter or receiver can be charged while in operation.

►

▷

Plug the small end of the USB charging cable into the USB port on the

transmitter or receiver.

▷

Plug the large end of the USB charging cable into the USB port on a

conventional USB power supply unit.

▷

Plug the USB power supply unit into the wall socket.
The status LED indicates the charge level.

< 5%

5% – 75%

> 75%

100%

Using stickers to label transmission paths

You can use the colored stickers to show which transmitter belongs to

which receiver.

►

Summary of Contents for XS Wireless















































































Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands

Sennheiser XS Wireless, Instruction Manual

Search results

Summary of Contents for XS Wireless

Reviews:

Related manuals for XS Wireless

Brands by name

Popular brands