Seneca S203RC-D User Manual Download

Page: 46 / 64

USER MANUAL – S203TA-D / S203RC-D

Energy ratio

reactive energy.
to set Varh write 1
to set KVarh write 1000
to set MVarh write 1000000
etc…

bits

(KVarh)

40049(LS)

Cfg flags

Control

flags

bitwise.

(0 = LSB)
Bit

energy

values

protection  from  reset  through
RS485 (1 for enabled).
Bit  1  =  if  set  to  1,  the  digital
output  energy  sign  values
reactive  energy  instead  of
active energy.

Unsigned
16 bits

RW 0

40050

Demand Time

Time (minutes) on which the
average

active

power

evaluated

function

disabled)

Unsigned
16 bits

RW 15

40051

Cut off
current

Minimum

current

(mA)

necessary to activate the
energy counter.

Unsigned
16 bits

RW 50

40052

Command

Command register.

To reset the device, write

0xDEAD

To set a positive energy
value for phase A, write the
value

(in integer unsigned

32 bits format)

in Command

aux

(high

part)

and

command aux 2 (low part),
then

write

0xBACA

Command register

To set a positive energy
value for phase B, write the
value

(in integer unsigned

32 bits format)

in Command

aux

(high

part)

and

command aux 2 (low part),
then

write

0xBACB

Command register

To set a positive energy
value for phase C, write the
value

(in integer unsigned

32 bits format)

in Command

aux

(high

part)

and

command aux 2 (low part),
then

write

0xBACC

Command register

To set a negative energy
value for phase A, write the
value

(in integer unsigned

32 bits format, the firmware
add itself the sign)

Command aux 1 (high part)
and command aux 2 (low

Unsigned
16 bits

RW 0

40131

Summary of Contents for S203RC-D































































Search results

Summary of Contents for S203RC-D

Reviews:

Related manuals for S203RC-D

Brands by name

Popular brands

Seneca S203RC-D, User Manual

Search results

Summary of Contents for S203RC-D

Reviews:

Related manuals for S203RC-D

Brands by name

Popular brands