Seneca S203RC-D User Manual Download

Page: 4 / 64

USER MANUAL – S203TA-D / S203RC-D

2.10.

3-PHASE WITHOUT NEUTRAL INSERTION WITH CTS AND VTS ................... 15

S203RC-D ELECTRICAL CONNECTIONS ................................................................ 17

3.1.

S203 RC-D TERMINAL POSITIONS ....................................................................... 17

3.2.

SINGLE PHASE INSERTION .................................................................................. 18

3.3.

SINGLE PHASE INSERTION WITH VT .................................................................. 18

3.4.

ARON INSERTION .................................................................................................. 19

3.5.

ARON INSERTION WITH VTS ................................................................................ 19

3.6.

4 WIRE WITH NEUTRAL INSERTION .................................................................... 19

3.7.

3-PHASE WITHOUT NEUTRAL INSERTION WITH VTS ....................................... 20

ANALOG OUTPUT ..................................................................................................... 21

4.1.

ANALOG OUTPUT IN VOLTAGE MODE CONNECTIONS .................................... 21

4.2.

ANALOG OUTPUT IN CURRENT ACTIVE MODE CONNECTIONS...................... 21

4.3.

ANALOG OUTPUT IN CURRENT PASSIVE MODE CONNECTIONS ................... 21

DIGITAL OUTPUT ...................................................................................................... 22

5.1.

DIGITAL OUTPUT ELECTRICAL CONNECTIONS ................................................ 22

THE DISPLAY............................................................................................................. 23

6.1.

ELECTRICAL SYMBOLS ON DISPLAY ................................................................. 23

6.1.1.

4 WIRES INSERTION (WITH OR WITHOUT NEUTRAL) .................................... 23

6.1.2.

1 WIRE INSERTION ............................................................................................. 27

6.1.3.

ARON INSERTION ............................................................................................... 28

6.2.

DIAGNOSTICS PAGE ............................................................................................. 30

Summary of Contents for S203RC-D































































Search results

Summary of Contents for S203RC-D

Reviews:

Related manuals for S203RC-D

Brands by name

Popular brands

Seneca S203RC-D, User Manual

Search results

Summary of Contents for S203RC-D

Reviews:

Related manuals for S203RC-D

Brands by name

Popular brands