Senco Fusion F-LXP Operating Instructions Manual Download Page 9

9

SAFETY WARNINGS

Battery Use

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions for SENCO 
battery charger VB0156 (US). 

Before using SENCO battery charger VB0156 (US), read all instructions and 
cautionary markings on battery charger and battery.

Do not expose charger to water, rain, or snow.

Use indoors.

Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of 
fire, electric shock, or injury to persons.

To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or 
stress.

Length of Cord (Feet)

AWG Size of Cord)

Longueur du cordon (en m)

Taille AWG du cordon

Largo del cable (m [pies])

Calibre AWG del cable

25

150

100

50

7,5

45

30

15

16

14

16

16

16

14

16

16

16

14

16

16

7,5

45

30

15

RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY 
CHARGERS

An extension cord should not be used unless absolutely necessary. Use of im-
proper extension cord could result in a risk of fire and electric shock.

If extension cord must be used, make sure:

•  That pins on plug of extension cord are the same number, size, and shape as  
  those of plug on charger; 
•  That extension cord is properly wired and in good electrical condition; and 
•  That wire size is at least as large as the one specified in the table.

Do not operate charger with damaged cord or plug. If damaged, have replaced immediately by a qualified 
serviceman.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take 
it to a SENCO Authorized Service Center.

Summary of Contents for Fusion F-LXP

























Reviews: