Senco Fusion F-LXP Operating Instructions Manual Download Page 21

21

TROUBLESHOOTING

Problem/Symptom

Probable Cause

Corrective Action

Tool runs but will not drive 
fastener.

Battery is discharged or has a 
dead cell.

Recharge or replace with fresh 
battery.

Staple jam in guidebody.

Refer to operators manual for 
jam-clearing instructions.

Mechanism requires repair.

Return tool to authorized SENCO 
service representative.

Tool is overheated.

Allow tool to cool and insert fresh 
battery.

Driver tip not located above 
fastener.

Recharge battery and allow tool to 
automatically retract driver.

Poor feed/ tool jamming.

Debris build-up in mechanism.

Clean tool, clean magazine or 
inspect feeder spring.

Driver tip not located above 
fastener.

Broken or worn driver.

Return tool to authorized SENCO 
service representative.

Tool does not fully return.

Weak battery.

Recharge battery and allow tool to 
automatically retract driver.

Ensuring the long life of your Cordless Finish tool

Welcome to SENCO’s family of products. SENCO brings 50 years of commitment to our customers and to power fastening 
systems. We are dedicated to making sure your tools are performing at their best, and we understand that ensuring the 
long life of your tools is important. Here are some operational and service tips.

•   Start with fully charged batteries at the beginning of each work day.
•   Set the depth of drive on your SENCO tool so fasteners are not over-driven.
•   To maximize battery life, follow storage recommendations and charging recommendations in this manual.
•   Keep your Cordless Stapler as clean and free of debris as possible.
•   Service your SENCO tool periodically to insure your tool is productive and helping you earn money on the job.  
  See the service guide below for recommended service intervals.

If your Cordless Stapler does require service, dedicated SENCO servicing dealers are available for you. For the location 
nearest you, call SENCO’s Action line at 1-800-543-4596 or visit SENCO’s website (www.senco.com).

Recommended service includes

•  Check Electrical System
•  Check Feed System
•  Check Drive Track
•  Add Grease to Piston and Driver

Summary of Contents for Fusion F-LXP

























Reviews: