background image

10

Do not disassemble charger or battery cartridge; take it to a SENCO Authorized Service Center when service or 
repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.

104° F

40° C

32° F

0° C

Do not charge battery cartridge when temperature is BELOW 0˚C (32˚F) or  
ABOVE 40˚C (104˚F).

Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

Do not recharge non-rechargeable batteries.

Do not allow anything to cover or clog the charger vents.

Do not store the tool and battery cartridge in locations where the temperature may reach or exceed  
45˚C (113˚ F).

Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery 
cartridge can explode in a fire.

Never attempt to connect two (2) chargers together.

This appliance is not intended for use by young children or infirm persons unless they have been adequately 
supervised by a responsible person to ensure that they do not play with the appliance.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or men-
tal capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 
concerning use of the appliance by a person responsible for their safety. Children should be supervised to 
ensure that they do not play with the appliance.

For more safety information, go to www.senco.com 
and safety training materials and programs visit the 
ISANTA website at www.isanta.org. 
www.P65Warnings.ca.org.

BATTERY AND CHARGER SAFETY WARNINGS

Summary of Contents for Fusion F-LXP

























Reviews: