Senco Fusion F-LXP Operating Instructions Manual Download Page 3

3

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL

SIGNAL

MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or 
serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or 
serious injury.

CAUTION:

Indicates a hazardous situation, which, if not avoided, may result in minor or 
moderate injury.

NOTICE:

(Without Safety Alert Symbol) indicates information considered important, but 
not related to a potential injury (e.g. messages relating to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning.  

Proper interpretation of these symbols will allow you to operate the product in a better, safer manner.

SYMBOL

NAME

DESIGNATION/EXPLANATION

Safety Alert

Indicates a potential personal injury hazard.

Read Operator’s 

Manual

To reduce the risk of injury, user must read and understand operator’s manu-
al before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply with ANSI 
Z87.1.

Do not rest your finger on the trigger when picking up the tool, moving 
between operating areas and positions or walking, as resting finger on trigger 
can lead to inadvertent operation. For tools with selective actuation, always 
check the tool before use to ascertain the correct mode is selected. 
This tool has either selective actuation for contact actuation or continuous 
contact actuation by actuation mode selectors or is a contact actuation or con-
tinuous actuation contact tool and has been marked with the symbol above. 
If using this tool in selective actuation mode, always ensure it is in the correct 
actuation setting.
Be careful when changing from one driving location to another.

R

Do Not Oil

Routine lubrication is not necessary.

Wet Conditions 

Alert

Do not expose to rain or use in damp locations.

Recycle

This product uses Lithium-ion batteries. Local, state, or federal laws may pro-
hibit disposal of batteries in ordinary trash. Consult your local waste authority 
for information regarding available recycling and or disposal options.

V

Volts

Voltage

Direct Current

Type or characteristic of current

Summary of Contents for Fusion F-LXP

























Reviews: