６.HOW TO PRINT OUT
1.How to set the paper in the printer
●Besides the thermal paper S950 included
with this model, the thermal paper S951 is
available for printing out the stored data. It is
a long-type thermal paper that can print
out up to 2,800 lines. To use S951, the
paper holder SVAZ007 for exclusive use
with it is necessary.
□
１
Cut the first pasted position of the paper
straight.
□
２
Open the paper cover as shown in the
illustration.
□
３
Slide the power switch to "ON". At this
time, the motor runs for approximately 1
second to indicate that the power is
supplied.
□
４
Inset the end of the paper into the paper
insertion slot.
□
５
Keep the paper advancing switch pressed
until the end of the paper is advanced out 2
to 3 cm from the printer.
(Do not pull out the paper by force.)
□
６
Put the roll paper into the holder and
close the paper cover.
Be sure to set the paper with the right side up. It
can only be printed on one side.
（
）
If the roll paper gets out of shape, make it round
before inserting it into the holder.
（
）
Notes 1 Do not pull the paper in the reverse direction (opposite to the direction of
advancing the paper), as this will damage the printer. When replacing the
remaining roll paper with a new one, first cut the paper in the holder, then
remove the rest of it by pressing the paper advancing switch, or pull it out
in the direction of advancing the paper.
Notes
2 Be sure to use the roll paper S-950 for exclusive use with this model.
Otherwise, poor printing or malfunction will be caused.
Roll paper
Power switch
Paper advancing
switch
53
Printout after the measurement
SPLIT
RECALL
BLOCK
LAP
STOP
BATT.
LAP
F
E
SYSTEM STOPWATCH
300LAP
／
SPLIT MEMORY
POWER
ON
LOCK
LAP
／
SPLIT
RESET
START
STOP
CLEAR
1/100
STOP.W A/S SET
TIME
RECALL
（１）Turn on the power switch.
（２）Press memory recall
button (RECALL).
The time data stored in
memory are printed out.
＊When all the stored data are
printed out, the printer
automatically stops.
g
STOP-W. A/S SET TIME
SPLIT
RECALL
BLOCK
LAP
STOP
BATT.
LAP
F
E
SPLIT
RECALL
BLOCK
LAP
STOP
BATT.
LAP
F
E
(Start data)
Recall button
① Memory recall
Show the memory recall display, and
select the block of data you wish to
print out.
(Printout display for desired block of data)
Recall button
②Turn on the power switch of the printer.
③Keep recall button pressed.
When the stopwatch confirms the
"Power on" of the printer, flashing
"Print" is displayed.
Block No. for the block of data to be printed
RECALL
STOP
BATT.
LAP
F
E
The total elapsed time of the block is displayed.
・If recall button is released immediately after flashing "Print" is displayed, the printout
will be canceled and the display returns to the memory recall display.
④ Keep recall button pressed for 1 second, and then release it as "Print" stops flashing and remains displayed.
The data in the selected block is displayed quickly one after another, and then printout is started.
(While the data in the block is displayed quickly one after another, the
stopwatch checks for the fastest lap time in the selected block.)
・The stored data can be printed out as many
times as necessary.
・Printout can be selected from only the desired
block of data and all the blocks of data.
"Printout of the desired block of data"
55
２.Printout
Printout during the measurement
□
１
Turn on the power switch for printer before starting
the measurement. When the switch is turned on, the
roll paper is advanced by one line.
□
２
Operate print mode selection switch to select the
printout from "lap time only" and "both split time and
lap time".
SYSTEM STOPWATCH
POWER
ON
Print mode
selection
switch
Power switch
LAP
SPLIT
SPLIT
Both split time and lap time are printed out.
(print mode selection switch)
Only split time is printed out.
cc
□
３
After the measurement is started, the identification number (if it is set), block
number, starting time, date, month and year are printed out, and then the
time data are printed out successively as soon as they are measured.
LAP
SPLIT
SPLIT
Block number BLOCK:1
Year･Month･Date 1999 10 10
Start time START 10:19
SPLIT
1-0:05′03 76
2-0:05′12 33
3-0:05′41 13
4-0:05′59 06
5-0:06′17 88
6-0:06′43 56
7-0:07′21 47
8-0:07′36 48
Finish time /S/0:08′02 58
Block number BLOCK:1
Year･Month･Date 1999 10 10
Start time START 10:19
SPLIT/LAP
1-0:18′05 33
0:18′05 33
2-0:36′37 78
0:18′32 45
3-0:55′13 11
0:18′35 33
4-1:13′25 31
0:18′12 23
5-1:31′57 55
0:18′32 21
6-1:49′32 78
0:17′35 23
7-2:01′31 04
0:17′58 26
8-2:25′43 62
0:18′12 58
Finish time /S/2:54′02 77
Example of printout
Print mode selection
switch
Split time only
Both split time and
lap time
c
d
＊When the power switch of the printer is turned on after the measurement is started, the data is printed
out starting from the next measurement data.
LAP
SPLIT
SPLIT
Split time
Split time
Lap time
54
56
"To print out the data in all the blocks in memory"
①Turn on the power switch of the printer.
②Show the memory recall display, and keep recall button pressed. Flashing "Print" is displayed.
③Printout of all the blocks of data
・Keep recall button pressed further until "Print All" is displayed.
④Then, release recall button. The data in all the blocks is displayed
quickly one after another starting from Block "1", and will be
printed out at a stretch.
(While the data is displayed quickly one after another, the
stopwatch checks for the fastest lap time in each block.)
Notes:
＊While the printout is under way, none of the stopwatch buttons will work.
・Once started, the printout cannot be canceled halfway.
・Even if the power switch of the printer is turned off while the printout is in progress, the button operation of the stopwatch is nullified until entire
data to be printed is shown on the display.
SPLIT
RECALL
BLOCK
LAP
STOP
BATT.
LAP
F
E
(Printout of all the blocks of data)
Recall button
