manualshive.com logo in svg

Segger Flasher ATE, User Manual

Share
Download
Segger Flasher ATE User Manual Download Page 37

37

CHAPTER 3

Universal Flash Loader mode

3.3.1.4    Configuration Data for ST STM8

HighSpeed

The interface mode (0 = low speed / 1 = high speed) used for communication.

ROP

Read out protection configuration byte: Depending on the target, 

0x00

 or 

0xAA

.

SectorSize

Sector size: Depending on the target: “64” for low density flash memory, “128” for medium

or high density flash memory.

Pins are connected as follows:

Flasher Interface

Signal

Pin 1

VCCT

Pin 2

VCCT

Pin 4

GND

Pin 6

GND

Pin 8

GND

Pin 9

SWIM

Pin 10

GND

Pin 12

GND

Pin 14

GND

Pin 15

Reset

Pin 16

GND

Pin 18

GND

Pin 20

GND

Note

As the STM8’s option bytes are part of the data image, the data image must not enable

the read out protection for the device in order to allow verification after programming.

The read out protection can be set finally by enabling the step “Secure”. This function

only changes the ROP option byte to the appropriate value.

Flasher ATE User Guide (UM08035)

© 2017-2018 SEGGER Microcontroller GmbH

Summary of Contents for Flasher ATE









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands