Seepex BN 100-6LS Operating And Assembly Instruction Manual Download Page 39

Page: 39 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

11 (18)

Dismantling/reassembly

9.1.3.5 Segment retainer (671) - dismantling - pressure branch

9.1.3.6 Rotating unit (RTE) – Dismantling

with flush connection

without flush connection



Dismantle the segment retainer (671) on
the suction casing (500).



Remove the O-ring (731) from the centring
recess on the suction casing (ZA, 500).

Tool (W10/dismantling tool)



Remove the flushing connection (SSÜ) on
the casing of the shaft seal (SEA).



Lift/slide splash ring (310) and turn out
plug-in shaft pin (309).



Pull the rotating unit (RTE) with shaft seal
(SEA) off from the output shaft of the drive
(ANT).



Dismantle shaft seal (SEA).

–

Note dismantling the shaft seal

(chapter 9._).

Tool (W10/dismantling tool)



Lift/slide splash ring (310) and turn out
plug-in shaft pin (309).



Pull the rotating unit (RTE) with shaft seal
(SEA) off from the output shaft of the drive
(ANT).



Dismantle shaft seal (SEA).

–

Note dismantling the shaft seal

(chapter 9._).

Summary of Contents for BN 100-6LS







































































Search results

Summary of Contents for BN 100-6LS

Reviews:

Related manuals for BN 100-6LS

Brands by name

Popular brands

Seepex BN 100-6LS, Operating And Assembly Instruction Manual

Search results

Summary of Contents for BN 100-6LS

Reviews:

Related manuals for BN 100-6LS

Brands by name

Popular brands